![]() With its narrow strakes and closely spaced steam-bent frames, there were hundreds of index-card-sized patches of planking to sand, and I didn’t want to subject my fingertips and knuckles to that kind of torture. I bought Dremel’s Multi-Max 6300 (superseded by the Multi-Max MM30) to diminish the misery of sanding the interior of my bright-finished lapstrake Whitehall. It comes as a kit with blades, accessories, and case for prices as low as $119. Their adventure blog is The DeWalt DWE315 is available from several stores and online vendors. Current boat works projects include restoration of a wooden Sunfish and new build of a diamond-bottomed catboat. Kent Lewis and his wife Audrey maintain a fleet of small boats in Northwest Florida. You may find one of them that is a worthwhile addition in your shop. With sharp teeth, the work is easier and goes much quicker.īosch, Dremel, Fein, Hitachi, Porter Cable, and Rockwell all manufacture oscillating multi-tools. We put one on our electric drill to sharpen burned-up blades in minutes, saving the time and money that comes with a trip to buy new blades. Ridge Carbide makes a blade sharpener that is a stack of fifteen 3″ metal-cutting discs, separated by 1/16″ rubber washers on a 3/8″ arbor. The teeth of wood-cutting blades can get dulled quickly by some materials a dull blade will cut slowly and may even begin to smoke. The powerful 3-amp motor has been up to all the jobs we’ve done with the tool. The DeWalt has a variable-speed control trigger-rather than a switch as on some other models-and continuous-on trigger lock. We like the long 10′ cord and the LED work light on the tool. The DeWalt comes with a universal adapter, meaning we can use the full array of blades available, no matter which of the half-dozen fitting attachment configurations might have. We switch blades frequently when we work on seams and planks, and having to use a tool to change blades slows the work down and risks losing the fastening screw and washer. It has a system that allows fast blade changes, without having to use a tool. When we went shopping for a multi-tool we did our research and settled on DeWalt’s DWE315. The built-in light comes in handy for working in tight, poorly lit spaces. Triangular sanding pads can do sanding in small spaces that other sanding tools can’t reach, even all the way into corners scraper blades speed up paint and excess epoxy removal. Oscillating multi-tools do more than cutting. If you’ve enjoyed using Japanese handsaws, there are multi-tool blades with teeth cut in the same way they’re well suited for working with hardwoods. With a blade designed to cut through wood and nails we can cut through fastenings in the laps between planks. We’ve used the oscillating multi-tool to put scarfs into planks, doing those repairs while the planks were still attached to the boat. For long, straight cuts a blade guide is a useful attachment it can also be used as a depth stop. The blades are small, have a small range of motion, and can be attached at different angles, so the tool can reach into tight spaces or around corners. The plunge-cut of oscillating saw blades allow us to precisely remove areas of rot and neatly trim the surrounding wood for dutchman repairs. We found a semicircular blade handy for reefing out caulked or glued seams and also for scribing and trimming a bevel along plank edges. The DeWalt multi-tool has aa variable speed trigger switch and a quick-release device for a rapid, tool-free change of blades.īlades for multi-tools tools come in different shapes and materials for use with metal, fiberglass, or wood. Its speed can be controlled for different materials: slower for metals and faster for wood. The multi-tool has a side-to-side rotating blade that swings just 1.6 to 5 degrees at up to 23,000 oscillations per minute. The tool was an oscillating multi-tool, and I quickly started thinking of the potential uses for boatbuilding and repair. A section of it was rotten, and I imagined he would replace the entire piece, but instead he pulled out an amazing tool, made a plunge cut straight into the trim, and removed only the rotten section. A few years back, I was watching my carpenter friend fix the trim around a door.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |